| CAS No.: | 1344281 |
|---|---|
| Formula: | Al2O3 |
| EINECS: | 215-691-6 |
| Samples: |
|---|
| Customization: |
|---|
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
| Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
Suppliers with verified business licenses
Audited Supplier LOCTITER PC 7226 Fine Particle Wearing Compound is a grey, two-part, trowelable, carbide-filled, epoxy-based wear protection coating that effectively protects equipment from fine particle abrasion.
| Application method | Trowel |
| Applications | Protective Coating |
| Color | Gray |
| Cure type | Room Temperature (Ambient) Cure, Two Component Mix |
| Drying time | 6.0 hr. |
| Key characteristics | Abrasion Resistant, Prolongs Equipment Life, Renews Worn Surfaces, Sag: Non-Sag, Wear Resistant |
| Mix ratio, by volume | 2 : 1 |
| Particle size | Large |
| Physical form | Paste |
| Substrates | Metal |
1. Cyclone and separator bodies
2. Dust collectors and exhausters
3. Pump liners and impellers
4. Fan blades and housings
5. Chutes and hoppers
6. Elbows and transition points
1. Cleaning:Remove dirt,oil, grease,loose flanky rust etc.,with a suitable high pressure water cleaning system .
2. Blasting:Blast all surfaces to be coated,with a sharp edged angular grit,such as aluminum oxide,to a depth of profile of approximately 75 microns and a degree of cleaniness of very thorough Blast Claeaning/Near Whitef.
3. Cleaning:After blasting metal surfaces should be cleaned with a waterless or solvent,and allow the surface to dry before application of the product coat the surface before any oxidation or contamination takes place.
4.Protection From Flash Rusting:To avoid flash rust,repairs should be made as soon as possible or within a mixmum 2 hours of blasting.
5. Mixing The Material:Measure 2 parts resin to 1 part hardener by volume or weight if doing a partial kit.Otherwise,mixing a full kit is pre-measured at the correct ratio.For a full kit mix ,a spiral mixing blade attached to a high torque electric or pneumatic drill can be used.For a partial kit transfer measured quantities onto a clean and dry mixing surface to mix together witha trowel until uniform in color.If resin and hardener temperatures are 15ºC or below,preheat resin only,to about 30ºC but not to exceed 40ºC.
6. Application:Apply fully mixed material to the prepared surface.Initially apply the material in a very thin layer to "wet" out the surface and ensure full epoxy contact with the roughened surface. Build up to desired thickness(minimum 6 mm),avoiding air entrapment.At 25ºC,the working time is 15 minutes and functional cure time is 4 hours Working and cure time depend on temperature and mass the higher the temperature and the larger the mass,the faster the cure.
500g/set, 5kg/set, 10kg/set, 13.7kg/set and 20kg/set
10kg/set carton size: 32x32x32.5
Thank you for you interest in our products. Glad to say we are qualified to supply some top brand adhesives& sealants equivalent. Many old clients are satisfied with our quality, now established strong cooperation with us. OEM is welcome, you just send us your spec. and labels. Then we will arrange the rest: production, shipping documents(air& sea), customs clearance files... Most of time, we get 5 positive feedback from clients both quality and service. Work with us can save your time and money, so you will have more time to company your family. Our work aim is to provide clients high quality products with competitive price& good service.
FAQ
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}